Car Amplifiers Installation Kits

Whether it’s in your car, motorcycle, home, or your office, the Boostaroo audio amplifier can go wherever your satellite radio can go. Simply plug a Boostaroo into the headphone jack of your XM Radio, then plug in your headphones to one of the 2 output jacks, and you’ll get at least double the volume. Your audio will be clear and crisp, with no added distortion from your satellite radio. It is nothing short of spectacular. I just love it. It was easy to splice into my satellite radio on my motorcycle and it is so loud I can hardly turn it up. I read the site and reviews. I didn’t know if “doubling” the sound was going to be enough for my Sirius radio I installed on my motorcycle. I took a chance, thinking if I didn’t like it I could return it. I installed it in the parking lot and about blew my ear drums out!

ASK A BRAND

This model in particular is a double din stereo unit, featuring a beautifully lit 6. The keys are able to light up, along with various background customization options available under setup. Maximum power output is 50 watt amps per speaker and 22 watt amps RMS per speaker. Being a single-din design, what you get is extremely easy to access. With a detachable face plate, you can drastically reduce motorized theft. One of the best car stereo receivers on the budget you can get right now and very easy to install.

Oct 08,  · I have 2 Kenwood 10″ car subs in my HT setup. they are driven by a seperate NAD amplifier, which is switchable between 4 or 8 ohms. My pioneer reciver is sending the Sub pre-out signal to .

Most receivers have either preamp-in and preamp-out connections or tape monitor connections. In most cases, these are the best way to connect an equalizer to your stereo. Connecting to the tape monitor channels will require connection to only your receiver. Learn how to hook up an equalizer to the receiver instead. To run a signal from your stereo receiver to the equalizer and then to your amplifier, you will need 2 sets of RCA cable the same kind that is usually used to connect source components like turntables and CD players.

The length of the RCA cables should match the length of the distance between the receiver and the equalizer. Connect one pair of cables to the pre-amp output channels on the receiver and the other end of the cable to the left and right channel inputs on the equalizer. You will usually find these channels on the rear of the equalizer.

Right channel jacks will usually take the red colored RCA plug while left channel should take white or black RCA plugs. Connect the other pair of cables from the output channels on the back of the equalizer to the left and right input channels on the amplifier. The amplifier should remain connected to the receiver with an RCA cable between the amplifier outputs and the amp inputs on the receiver.

How To Properly Hook Up Speakers to Amps

How do you hook up a new car stereo? Well it helps if you have a repair manual for your car so that you can reference the wiring schematic for the stereo connections it will eliminate a lot of guess work. Using a multimeter find a wire in the connector in the dash that was formerly on the stock radio that has 12 vol…ts when the key is off and this will be your Batt.

Now with the key on find a second wire with 12 volts and this will be your Ign. If you have a power antenna there should be a connection for that on the new stereo and the wiring schematic will tell you which one that is.

If you run an amplifier and/or second battery, the PP, and PP are good choices for a quick disconnect for wire sizes up to 2/0. The only drawback is the .

This is different from a home electrical system, which uses alternating current AC and provides to volts at a lower current. The power supply will provide the power needed by the amplifier. Power supplies take alternating current and convert it into direct current. First, the alternating current goes through a transformer, which steps down the voltage and increases the current level. Then a bridge rectifier–a set of four diodes that allow current to flow in only one direction–forces the output of the transformer to stay constant.

Remove 1 inch of insulation off the other end of the red power wire.

Can I use car subwoofer with my home system?

Originally Posted by kevmatic I don’t think there is anything unsafe at all with using a car PSU to power a car amp However, due to the high currents involved the rewiring must be approached carefully. Any connection that’s not very good will turn into a mess quickly.

The sub sonic filter on your KX amplifier is designed to clean up your subwoofer system. It will reduce or eliminate low frequency “trash” present in some musical program material that you can’t hear but your amplifier wastes power trying to amplify.

Automotive wiring in a Pontiac Grand Prix vehicles are becoming increasing more difficult to identify due to the installation of more advanced factory oem electronics. One of the most time consuming tasks with installing an after market car stereo, car radio, satellite radio, xm radio, car speakers, tweeters, car subwoofer, crossovers, audio equalizer, car amplifier, mobile amp, car amplifier, mp3 player, ipod or any car audio electronics is identifying the correct color car audio wires for your Pontiac Grand Prix.

The Modified Life staff has taken all its Pontiac Grand Prix car radio wiring diagrams, Pontiac Grand Prix car audio wiring diagrams, Pontiac Grand Prix car stereo wiring diagrams, Pontiac Grand Prix car radio wiring schematics, Pontiac Grand Prix car wiring diagrams and cataloged them online for use by our visitors for free. Our automotive wiring diagrams allow you to enjoy your new mobile electronics rather than spend countless hours trying to figure out which wires goes to which Pontiac Grand Prix part or component.

Use of the Pontiac Grand Prix wiring information is at your own risk. Always verify all wires, wire colors and diagrams before applying any information found here to your Pontiac Grand Prix. Adding More Information If you would like to help the Modified Life community by adding any missing information or adding a new car audio wire diagram to our resource, please feel free to post it at the bottom of this page.

The radio harness does not provide a switched power source. Run a wire to the fusebox or ignition switch harness for switched power. Car Radio Ground Wire: Violet Car Stereo Dimmer Wire:

How to Wire an Amp & Subwoofers Into a Stock Stereo

Rated at 1, watts, you can comfortably get consistent watts of RMS power going directly to your subwoofer. With this Pioneer amp, you can adjust the subwoofer accordingly from at little as 40 Hz to as much as Hz. The newer amps including this one have a wired bass control module, allowing you to turn the bass level up or down without having to physically go to the amp itself and do it. The speaker level inputs allow you to connect your OEM headunit without having to buy add-on adapters or anything that does not have RCA-inputs.

This tiny audio amplifier is based on the Texas Instruments TPAD1. It can drive an 8-Ohm speaker at up to Watts; it won’t shake a stadium, but it will provide plenty of volume for your audio projects. Connect your line-level audio input to the IN + and – header. Connect your speaker to the.

To really highlight the bass of your car stereo, you need a setup capable of properly reproducing low frequency notes. Adding a subwoofer and amplifier to your existing stereo is a great way to improve the bottom-end output of your system and is one of the most common upgrades performed on a car’s audio gear. You have two basic options: You can purchase a separate amplifier and speaker or you can purchase a powered subwoofer with a built-in amplifier.

When purchasing either form of amplification, look for an amp that accepts high-level signals. This allows you to run a high level speaker signal from your stock stereo’s powered head unit without any additional wiring. If you purchase an amp without speaker level inputs, you will need to also purchase a line-out converter to alter the output of your stock head unit to a low-level signal to be accepted into standard speaker connections on your amp.

How Do You Hook Up A Mono Amp To Two 12 Subs

The following is the most basic system. It involves a head unit HU and 2 pairs of speakers which are driven by the head unit’s internal amplifier. You can see that the battery terminal of the HU is connected to a constant source of power the battery with an inline fuse. The accessory wire for the HU is connected to a power source which only has power when the ignition switch is in the ‘on’ or ‘acc’ positions.

The PLM is a watt monoblock class A/B amplifier that will shake up your car amplifier New & Now. 10 Backpacks So Stylish She’ll Think You Have Perfect Taste. This amp will allow you to hook up5 speakers, and get surround sound! You .

Next How to hook up the power antenna on my car’s aftermarket amplifier? I’ve been told to hook up the power antenna cable from your amp by just wrapping it around the already connected power antenna wire in the wiring harness from when the aftermarket head unit was installed, thus creating a taped 3-way connection of wires. This can’t be right, or safe for that matter. What is the correct method to hooking up the power antenna wire from your amplifier to your vehicles head unit?

If you have links to step by step tutorials or a video that would be great. Any video I’ve seen simply tells you to hook it up, not how to hook it up. I have been told some head units have a specific place on the back of it to hook up your power antenna, thus completely bypassing the wiring harness. Mine doesn’t say anywhere on it anything about a separate power antenna hook up for amps. There are things back there that aren’t being used but they’re not labeled so I don’t know what they’re for.

Also, my cd player’s manual has no wiring diagram or information on hooking up amplifiers.

How to hook up the power antenna on my car’s aftermarket amplifier?

Alternator whine is caused by a difference in electrical potential voltage between two points. It’s usually caused by a ground connection that is less than ideal. The main culprits are the amp, the head unit and any intermediate components such as crossovers and equalizers. Basically any component that touches the low level music signal from RCA cables.

4-Channel Amplifiers Information A 4-channel amplifier is the best way to power a complete set of new car speakers. These amplifiers are designed to power four door speakers, although the right & left channels can usually be bridged to offer a wide range of wiring options.

Class AB amps combine the good points of class A and B amps. They have the improved efficiency of class B amps and distortion performance that is a lot closer to that of a class A amp. With such amplifiers, distortion is worst when the signal is low, and generally lowest when the signal is just reaching the point of clipping. Class AB amps like class B use pairs of transistors, both of them being biased slightly ON so that the crossover distortion associated with Class B amps is largely eliminated.

Class C amps are never used for audio circuits. They are commonly used in RF circuits. Class C amplifiers operate the output transistor in a state that results in tremendous distortion it would be totally unsuitable for audio reproduction. However, the RF circuits where Class C amps are used employ filtering so that the final signal is completely acceptable. Class C amps are quite efficient. Due to improvements in the speed, power capacity and efficiency of modern semiconductor devices, applications using Class D amps have become affordable for the common person.

Satellite Radio Amplifier

Cars use thicker cable due to the high amount of current being drawn from the battery lower voltage appliances tend to draw more current then higher voltage ones, it also helps reduce voltdrop. Someone has said that CCA is what you want to look for on a car battery this is incorrect as Cold Cranking Amps are for when the car is cold and you try to start the engine its designed for a very short duration while keeping a voltage of 12V, the actual battery usage you need to look at is measure in Ah these are usually much smaller then the CCA and are the rating you can safety continuously draw from a car battery.

Note for the writer its a great article but i wouldn’t recommend soldering then crimping, solder is very soft and will become loose after a while your better off crimping stright on the copper. I have recently hooked up my Amplifier to a PCU. But I only used one black and one yellow wire of the PCU to power it.

Now all we have left is to hook the speakers up! Make sure the resistance of your speakers is not lower than what your amplifier is capable of handling, for instance never put a 1-ohm load on an amplifier that is only 2-ohm stable.

While holding, turn dock ON d. Front LED will blink 2-digit software version number e. What type of USB charging does Kicker products support? What battery to I need for my IR remote? How do I get support if I have a problem? If you are having a problem with any of your Kicker products you can contact us at either and ask for Technical Support or email us at support kicker. Our business hours are Monday — Friday, 8: How can I tell what model I have? On the underneath side of the dock is a label that will have the model name of your dock.

To pair to an Amphitheater K3:

McIntosh Amplifier

To try to get this working, I recently purchased a secondary amp with RCA inputs to power the extra speakers. The additional speakers 5 pairs are mounted in the ceilings throughout the house. I also have a speaker selector box so that I can select which room or rooms I want to send the sound to. The output can be mono. I just want some sound to the other rooms.

Jan 14,  · Does anyone know how to hook up a car sub to a home theater system. I already have a powered sub hooked up to a home theater amp, but i don’t know how to hook up the car sub to it.

Do all stereos use the same connection to hook up? The thing is, the person that had it before me did some stuff, and it has a fairly new radio in it already. So, if I buy a radio with an audio in jack, will I just be able to take out the old one and plug the new one in? Also, I’ve got a right and left RCA audio plug behind the seats from the last guy that had it, no doubt , and there’s a red cable that starts behind the seats and goes up right next to the battery, but it isn’t hooked up.

If I wanted to get new speakers he didn’t leave speakers in it , will I have to look for any specific kind that have an RCA plug, and secondly, how will I power them? Just hook up that wire to the positive terminal and to the speakers? Sorry for the wall of text, I’m just really confused with all this new stuff. DO NOT connect the red wire to anything but the power inlet of an amp. The speakers will require sperate wires to power them. The connections for a headunit are pretty much standard – you will need a wire that has 12V power all the time, one that has 12V only when the switch is on and a black wire connected to the metal frame of the car for ground.

Will the amp always be on, or will it turn off when I turn off the head unit? If I leave the red wire hooked up to the terminal when the pickup is turned off, will it drain the battery? OH I just remembered, there’s also a little tiny wire back with the RCA plugs and red wire, would that be the connection to the head unit?

How to hook a car amplifier to your house !